The DPF1/2MIMFRS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System.  

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFRS - Substitute Sediment Pre-Filter for RainSoft Part # 9338, 9528, 9531, 9547, 9577, 9591, 9596, 9738, 9747, 9757, 12461, 12464, 13110, 13119, 17367, 17368, 18557, 18773, UF-10 (Must Use With MEM12TFCRS-93 Membrane)

The MEM12TFCRS-93 .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM12TFCRS-93 - Substitute Membrane Filter for RainSoft “93 Series” Part # 9339, 9744, 17379, CTA-RS12-10 (Must Use With DPF1/2MIMFRS and DPF1MMFRS Dual-Purpose Filters)

The CF1/2MILRS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

 CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

 CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

The DPF1/2MIMFRS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

MEM12TFCRS-93 - Substitute Membrane Filter for RainSoft “93 Series” Part # 9339, 9744, 17379, CTA-RS12-10 (Must Use With DPF1/2MIMFRS and DPF1MMFRS Dual-Purpose Filters)

The MEM12TFCRS-93 .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

 CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

The CF1/2MCBRS (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters, also allowing better filtration of the Fine  Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as a Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

The DPF1/2MIMFRS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFRS - Substitute Sediment Pre-Filter for RainSoft Part # 9338, 9528, 9531, 9547, 9577, 9591, 9596, 9738, 9747, 9757, 12461, 12464, 13110, 13119, 17367, 17368, 18557, 18773, UF-10 (Must Use With MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Membranes) d

The MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd).001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Substitute Membrane Filter for RainSoft Part # 9564, 9565, 9744, 9590, 9591, 9593, 9594, 12448, 13016, 17374, 17375, 17376, 17379, 21173, 21176, UF-10 (12 gpd), Part # 9568, 9596, UF20, UF22, UF22T, UF20, 21176 (24 gpd), Part # 12477, 17370, 18571, 18644, 21179, UF50, UF50T (50 gpd) (Must Use With DPF1/2MIMFRS and DPF1MMFRS Dual-Purpose Filters)

The CF1/2MILRS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

The DPF1/2MIMFRS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFRS - Substitute Sediment Pre-Filter for RainSoft Part # 9338, 9528, 9531, 9547, 9577, 9591, 9596, 9738, 9747, 9757, 12461, 12464, 13110, 13119, 17367, 17368, 18557, 18773, UF-10 (Must Use With MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Membranes)

The CF1/2MILRS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

The MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd).001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Substitute Membrane Filter for RainSoft Part # 9564, 9565, 9744, 9590, 9591, 9593, 9594, 12448, 13016, 17374, 17375, 17376, 17379, 21173, 21176, UF-10 (12 gpd), Part # 9568, 9596, UF20, UF22, UF22T, UF20, 21176 (24 gpd), Part # 12477, 17370, 18571, 18644, 21179, UF50, UF50T (50 gpd) (Must Use With DPF1/2MIMFRS and DPF1MMFRS Dual-Purpose Filters)

The CF1/2MILRS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILRS - Substitute Inline Carbon Post-Filter for RainSoft Part #  9568, 9760, 9798, 12470, 12471, 12740, 12741, 13137, 17369

The DPF1/2MIMFRS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFRS Substitute Sediment Pre-Filter for RainSoft Part # 9338, 9528, 9531, 9547, 9577, 9591, 9596, 9738, 9747, 9757, 12461, 12464, 13110, 13119, 17367, 17368, 18557, 18773, UF-10 (Must Use With MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Membranes)

MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd) Substitute Membrane Filter for RainSoft Part # 9564, 9565, 9744, 9590, 9591, 9593, 9594, 12448, 13016, 17374, 17375, 17376, 17379, 21173, 21176, UF-10 (12 gpd), Part # 9568, 9596, UF20, UF22, UF22T, UF20, 21176 (24 gpd), Part # 12477, 17370, 18571, 18644, 21179, UF50, UF50T (50 gpd) (Must Use With DPF1/2MIMFRS and DPF1MMFRS Dual-Purpose Filters)

The MEM12TFCRS (12 gpd), MEM24TFCRS (24 gpd), MEM50TFCRS (50 gpd).001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MCBRS - Substitute Carbon Post-Filter for RainSoft Part # 9531, 9757, 12464, 13119, 17368, 18557, 18773

The CF1/2MCBRS (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters, also allowing better filtration of the Fine  Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as a Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years